Графический редактор печатных плат P-CAD PCB


              

Графический редактор печатных плат P-CAD PCB



Соединений
Сообщения об ошибках программы PRO ROUTE
Текст сообщения об ошибке
Checkpoint file is incomplete
Conflicting width detected Net class will not be routed
The router's working storage limit
Storage required for fromtos can
Error opening router file File имя файла
Single fromto detected Connection will be skipped

Grid table overflow Some data will be skipped
Таблица сетки переполнена Некоторые данные будут опущены )
Unable to allocate memory for cost tables
Unable to allocate memory for wave front data
Unable to allocate memory for fromto data
Unable to allocate memory for padstack data
Error opening checkpoint file
Error writing to the checkpoint file
FORTRAN 77 input/output error Status статус ошибки
Too many grid points in the X or Y directions Required

Limit'
Reduce required grid points by using a coarser grid
Unable to allocate memory for
Inconsistent nested via ranges
Track outside circuit edge will
Pin outside circuit edge will
Via outside circuit edge will
(ПО вне контура ПП игнорируется
Unable to allocate segment data space
Unable to allocate memory for segment data

A pad references an undefined padstack Pad ignored
A via references an undefined padstack Via ignored
Error reading router input data
Less than значеаие working storage entries available
Via ranges will not peermit interconnection of all layers
Too many design rule classes for this pass
Vias are allowed to be closer
No passes were scheduled
A short was detected
Туре

А(n) объект on net цепь
Invalid number of manufacturing passes
Invalid number of iterative passes
Must be in the range
Nvalid check point interval
Must be in the range
Must be in the range
Router did not start or exited unexpectedly
Unable to open log file for writing
Log file name is not assigned

Log file does not exist
The maximum of значеыие
Error cleaning up design file
Unknown command received from the router замечание
Unknown error message from the router
The following files will be overwritten
The maximum of 15 net classes has been exceeded
At least one layer must be enable for routing
File name too long for router имя файла
File not found имя файла

Strategy file name missing
Error reading тип data
Error creating PCB object
Error displaying RGB object
Router file name is missing from PCB INI
Error preparing file for routing
Loading the strategy file will
Strategy file exists! "имя
Таблица 5 1 Пиктограммы программы PCAD ShapeBased Router
Таблица 5 2 Команды программы PCAD ShapeBased Router

Tools
Автотрассировщик Quick Route
Окно автотрассировщика Quick Route
Окно выбора шагов трассировки
Wide Line Routing
Horizontal
Vertical
"L" Routes
"Z" Routes
"С" Routes

Any Node
Maze Routes
Any Node (maze)
Route Cleanup
Via Minimisazion
Окно трассировщика Quick Route
Окно текущей информации о ходе трассировки
Strategy selections
Net classes
Wide line routing

Horizontal
Vertical
"L" routes
"Z" routes
"C" routes
Any node (2 vias)
Maze
Any node (maze)
Final statistics
Routing performance

Автотрассировщик Pro Route
Окно настроек трассировщика Pro Route
Окно выбора проходов трассировки
Manufacturing и Final Manufacturing
Wide Via Fanout (SMD)
Via Fanout (SMD)
Wide Initial
Wide Comprehensive
Memory
Initial

Comprehensive
Exhaustive
Iterative (Ripup)
Меню команды Route Cancel
Stop routing and save
Stop routing and do not save
Stop routing at end of this pass
Skip this pass and continue
Checkpoint route and continue
Бессеточный трассировщик PCAD ShapeBased Router

Настройка стратегии трассировки
Настройка стратегии трассировки
Memory (память)
Fan Out Used SMD Pins (веер)
Pattern (шаблон)
Shape Router Push and Shove (вставка и расталкивание)
Shape Router Rip Up (разрыв)
Clean During Routing
Clean After Routing
Evenly Space Traces

Add Testpoints
Установка параметров автотрассировщика
Параметры генерации контрольных точек электрических цепей
Установка атрибутов электрических цепей
Ручная трассировка
Интерактивная трассировка
Автоматическая трассировка
Автоматическая трассировка
Составление отчетов
Список формируемых отчетов по результатам трассировки

Содержание